← All projects

Live Oak Wall Paneling

Jurupa Valley, CA

Read the full project story
The finished wall. Painted pine paneling to 60 inches, with the designer's wallpaper from the top rail up to the crown.
Location
Jurupa Valley, CA
Materials
Primed pine 1x3 rails and stiles, every joint glued, biscuited and clamped with pinch dogs, then glued and nailed to the wall; Sherwin-Williams Emerald Urethane Trim Enamel, custom matched to the designer's fabric swatch
Timeline
3 days on site; no shop fabrication
Investment
$3,958

The Investment

$3,958

Turn-key total

3 days on site; no shop fabrication

Start to finish, on site.

What drove the cost

  • Pre-planning, site measure and material pickup: $350
  • Materials (primed pine 1x3, glue, biscuits, fasteners, adhesive): $420
  • Bench assembly at the house and installation, a day and a half: $1,550
  • Fill, caulk, prime and paint by Aztec General Painting in Sherwin-Williams Emerald Urethane Trim Enamel, custom matched to the designer's fabric swatch, a day and a half: $1,400
  • Floor protection, cleanup and haul-away: $238
  • Not included: the wallpaper and its installation, the interior designer's services, electrical work (no outlets were moved), and furniture and decor; no permit required for this project

The price is all-inclusive: design, materials, build, paint, and final detailing.

The story

How this project came together.

A Jurupa Valley bedroom wall built to an interior designer's rendering: a painted primed pine grid 60 inches tall across almost 15 feet of wall, with the designer's wallpaper above it.

This home is a newer custom build in a private gated community in Jurupa Valley. Nothing was broken and nothing was dated. The homeowners just wanted a little extra, and the wall behind the bed was 15 feet of plain painted drywall with a tall, dark headboard against it.

Interior designer Kathy Hernandez of Kathleen Ann Design drew the wall: the grid, the paired vertical pieces, the 60-inch height and the wallpaper above. The homeowners had already seen her renderings, and Holland & Sons built it the way she drew it. The one call made on site was sizing the paired stiles to flank the headboard and frame the outlets on both sides of the bed.

The whole wall had to be built downstairs and carried up a staircase, which is why it is primed pine 1x3 rather than MDF. Both side walls were plumb and parallel, so nothing had to be scribed. The crew built three long sections on assembly tables at the house, gluing, biscuiting and clamping every joint with pinch dogs, and all three were done by lunch.

After lunch the sections went upstairs, locked together with biscuits, and were glued to the wall and nailed off. Aztec General Painting then filled, caulked, primed and painted the paneling in Sherwin-Williams Emerald Urethane Trim Enamel, custom matched to a fabric swatch from the designer.

Three days on site, no shop fabrication, and no permit required for this project. The paneling and the designer's wallpaper do the work together.

The room with everything back in place. The paneling and the wallpaper do the work together.
The painted paneling up close. Sherwin-Williams Emerald Urethane Trim Enamel, matched to the designer's fabric swatch.
A pair of stiles sized to frame the outlet. The black clamps are pinch dogs, holding each glued joint tight while it sets.
Two biscuits standing up out of the rail, ready to lock into the next section.
One biscuit, glued into its slot. Every joint on this wall got one.
Looking down the length of a glued-up section before it went upstairs.
Wyatt setting the top section against the wall. "TOP" is penciled on the rail so nothing goes up upside down.
Wyatt nailing off the paneling. It is glued to the wall and nailed.
The right end of the grid, tight to the side wall. Both side walls were plumb and parallel, so nothing had to be scribed.
All three sections up and locked together, end of the carpentry. Paint is next.

Want something like this in your home?

Send us the room. We'll come measure, sketch, and quote, no obligation.

Start your project

Start the Conversation

Tell us about your project. Brian or one of the sons will reach out within one business day.

Want a ballpark first? See what past projects cost